3 mass produced auto parts could revolutionize the electric car industry by eliminating the need to charge or recharge

92 years ago Nikola Tesla removed the gasoline engine from a 1931 Pierce Arrow and replaced it with a 80 horsepower AC electric motor and drove the electric motor powered car at speeds of up to 90 mph. Since then it has been a mystery as to how he was able to power the Pierce Arrow using a 6 foot aerial antenna connected to a very small circuit box, 24 inches long, 12 inches wide and 6 inches high.

Unlike today’s electric cars there were no very expensive battery banks used. There was just one 12 volt Willard battery. A recently found tune-up manual for the Pierce Arrow stated that the Pierce Arrow battery was a Willard Type WJ 4-15. Capacity – 128 Amp hour (20 hr. rate).

For decades inventors and scientists have been trying to figure out how Nikola Tesla powered the electric engine. Solving that mystery can revolutionize the electric car industry. What they were concentrating on, in their research, was a complicated solution, whereas the solutions was staring them in the face every time they looked at their gas combustion engine car or truck. The mystery was solved since the very first gas combustion engine was built.

Dallas Morning News

The Electric Auto that almost triumphed: Power Source of ‘31 car still a mystery

by A.C. Greene,

January 24th, 1931

It is a mystery car once demonstrated by Nikola Tesla, developer of alternating current, that might have made electrics triumphant.

Supported by the Pierce-Arrow Co. and Westinghouse in 1931, he took the gasoline engine from a new Pierce-Arrow and replaced it with an 80 horsepower alternating current electric motor with no external power source.

At a local radio shop he bought 12 vacuum tubes, some wires and assorted resistors, and assembled them in a circuit box 24 inches long, 12 inches wide and 6 inches high, with a pair of 3-inch rods sticking out. Getting into the car with the circuit box in the front seat beside him, he pushed the rods in, announced, “We now have power,” and proceeded to test drive the car for a week, often at speeds of up to 90 mph.

As it was an alternating current motor and there were no batteries involved, where did the power come from?

A nephew of Nikola Tesla stated:

“under the hood, there was a brushless electric motor, connected to the engine. The engine was said to measure 40” long by 28” diameter. However, some of these figures may be estimates. Tesla would not divulge who made the motor.”

Take note that he stated that there were 2 electric motors in the engine compartment. “A brushless electric motor” was “connected to the engine”, a 80 horsepower electric motor. That’s significant because it starts to unravel the mystery as to how Nikola Tesla powered the Pierce Arrow with only one 12 volt Willard battery installed in the car.

“There was a voltmeter which was used to measure output of the receiver. Dr Tesla commented that the receiver had enough reserve power so that you could drive the car next to a house, connect the wiring, and light up the whole house.  …

After a time, and with increasing distance from the city itself, Dr. Tesla felt free enough to speak. Having now become sufficiently impressed with the performance of both his device and the automobile. Dr. Tesla informed his nephew that the device could not only supply the needs of the car forever, but could also supply the needs of a household “with power to spare”.

There is no mention in the Dallas Morning News or by Nikola Tesla’s nephew that Nikola Tesla removed the alternator of the Pierce Arrow. It just stated that the gasoline engine was removed and replaced with an 80 horsepower AC electric motor.

Alternators are used in all gas combustion engine automobiles to charge the battery and to power the electrical system when the engine is running. Even the Ford Model T automobiles from 1919 to 1927 had a 12 volt negative ground Delco style alternator.

It is entirely plausible that Tesla made use of the alternator to continuously recharge the Pierce Arrow’s single 12 volt automotive battery and supply sufficient power to the 80 horsepower AC electric motor.

There’s no mentioning that Tesla removed the Pierce Arrow’s ignition coil either. An ignition coil converts 12 volts to 30-40 kVs using a transitor or in Tesla’s case vacuum tubes.

Ignition coils existed back in the 1930s too. We know there was an ignition coil installed in the Pierce Arrow before it was converted into an electric motor car. The tune-up manual stated that the 1931 Pierce Arrow ignition coil was a Delco-Remy 526-B ignition coil. The Pierce Arrow tune-up manual also stated that it was mounted on the dash. A 12 volt battery wire also enters the dash and is connected to the key ignition.

The tune-up manual stating that the ignition coil was.mounted on the dash is a significant finding because:

The “power receiver” was then placed into the dashboard of the car and its wires connected to the antenna and to the air-cooled, brushless motor.

Note that the power receiver was connected to the “air-cooled brushless motor”, not the engine (was said to measure 40” long by 28” diameter).

The dash mounted ignition coil (also called a spark coil) is an induction coil in an automobile’s ignition system which transforms the battery’s low voltage to the thousands of volts needed to create an electric spark in the spark plugs to ignite the fuel. It is also entirely plausible that Nikola Tesla used the Pierce Arrow’s ignition coil to transform the antenna and/or the 12 volt car battery’s low voltages to thousands of volts (kVs) needed to power the electric motor.

An AC electric motors requires more than 12 volts of AC current. So all Nikola Tesla needed to do is use the Pierce Arrow’s ignition coil to transform the battery’s 12 volts into the required voltage needed to power the 80 horsepower AC electric engine.

A reasonable person would conclude that the 50 amps 12 volt alternator was used to continuously recharge the Willard 12 volt battery (128 Amp. hour) so that the Delco-Remy ignition coil could simultaneously keep on producing the required voltage needed to power the 80 horsepower AC electric engine. As a result, an electric car owner would never have to stop to charge or recharge an electric vehicle. The electric car would charge or recharge itself while it was driven.

The Dallas Morning News reported that there was a battery in the vehicle but it wasn’t used as the source of power. That’s isn’t entirely true. The battery was involved in powering the vehicle. The vacuum tube is used to make a small AC signal voltage into a larger AC voltage, thus amplifying it. A vacuum tube is a “valve” for electricity. Vacuum tube amplification is using a small amount of electric charge to control a much bigger amount of electricity that travels through the vacuum in a tube. Vacuum tubes require a filament voltage of at least 6.3 volts to produce high AC voltages. In the early days of electronics, vacuum tube (called valves in British contexts) devices were powered by batteries.

Therefore, 3 gasoline engine car parts, 1) a 12 volt battery, 2) an alternator and 3) an ignition coil could be repurposed to produce enough energy to power an electric car. Nikola Tesla proved it could be done 92 years ago.